EV Charger Installation
Level 2 EV charger installation in Humboldt County — Tesla, Emporia & more. Load calcs and permits handled by a C-10 licensed electrician. Free estimates.
Learn moreIf your panel is outdated, overloaded, or full, everything downstream suffers — flickering lights, tripping breakers, and no capacity for an EV charger or heat pump. Greenbelt Electrical replaces old panels with safe, code-compliant service sized for how you actually live.
Any one of these is worth a call. Several together usually means the panel is past due.
Panel upgrades make up about half of our work across Humboldt County — from 1960s Eureka homes with original fuse panels to rural properties with undersized service.
Main service equipment is the highest-stakes work in residential electrical. It should only be done by a licensed electrical contractor — not a handyman.
An old Federal Pacific, Zinsco, or fuse panel isn't just inconvenient — it's a known safety concern. We give you straight answers about what actually needs to be replaced.
Adding an EV charger or planning a remodel? Doing the panel upgrade at the same time usually costs less than two separate jobs. Ask us about combining the work.
Service size is the total power your home can draw from PG&E. Here is how the common sizes usually play out.
| Service size | Where you usually see it | What it typically supports | Room for EV, heat pump, etc. |
|---|---|---|---|
| 60 amp | Older homes, often with fuse panels | Basic lighting and outlets; struggles with modern appliances | Very little; usually an upgrade candidate |
| 100 amp | Many mid-century homes | A modest home, especially with gas heat and water heating | Limited; often tight once you add an EV charger or heat pump |
| 200 amp | Most new single-family homes | A typical modern home with electric appliances | Usually room for an EV charger and other added loads |
| Over 200 amp | Large or all-electric homes, homes with shops or multiple EVs | Heavy combined loads | Sized case by case |
General guidance only. We size every service with a load calculation based on your home, your appliances, and what you plan to add.
We don’t publish one-size-fits-all prices, because no two panels are the same. These are the things that move the number.
Replacing a panel at the same amperage is a smaller job than increasing service from 100 to 200 amps, which can mean a new meter base and service-entrance conductors.
An exterior panel next to the meter is simpler than an interior panel that has to be relocated or brought up to current clearance rules.
Corroded connections or problem circuits found during the job may need to be corrected so the new panel passes inspection.
Many older homes need new grounding electrodes or bonding to meet current code.
Service upgrades are coordinated with PG&E, and some need changes on the utility side of the meter.
Adding an EV charger or other new circuits at the same time adds parts and labor, but usually costs less than a second job later.
Every job is seen in person and quoted in writing before work starts. Call (707) 476-3720 or request a free estimate.
We inspect your existing panel, service entrance, and loads, then run a proper load calculation.
You get a clear, written price before any work starts — including permits and utility coordination.
We schedule the service disconnect with PG&E and pull the electrical permit — you don’t have to call the utility yourself.
The old panel comes out, the new one goes in, circuits are re-landed and labeled, and grounding is brought up to code.
The city inspection is completed and power is restored. A typical outage runs about 8:30 AM to 4:00 PM.
Humboldt County has a lot of older housing, from Victorian-era homes in Eureka to mid-century houses in Arcata, McKinleyville, and Fortuna. Many still run on original or decades-old electrical service that was never designed for today’s loads.
Our coastal climate is hard on electrical equipment too. Damp, salty air can corrode exterior meter bases, panels, and connections over time, so the condition of outdoor equipment is part of every assessment.
For service upgrades, we schedule the disconnect and reconnect with PG&E and coordinate the inspection with the local building department, so you don’t have to manage it yourself.
Based in Eureka and serving the whole county — including the surrounding North Coast communities.
Not sure if you're in our area? Call (707) 476-3720and we'll tell you straight.
Updated
Common signs: frequently tripping breakers, a fuse panel instead of breakers, a panel brand with known safety issues (like Federal Pacific or Zinsco), no open breaker spaces, or plans to add large loads like an EV charger or heat pump.
Typically about 8:30 AM to 4:00 PM on installation day. We schedule the shutoff with PG&E, replace the service equipment, and power is restored after the city inspection. We confirm the date with you in advance.
Yes. Service and panel upgrades require a permit and inspection. We handle the permit and coordinate the inspection as part of the job.
It depends on your home and what you plan to add. We size the service with a load calculation rather than guessing, then walk you through the recommendation before quoting.
Yes — this is one of the most common bundles we do. Combining the two means one permit, one service visit, and a panel sized for the new charger from day one.
It depends on your home. Service size, panel location, and the condition of the existing wiring all affect the price, so every panel upgrade is seen in person and quoted in writing before work starts.
A panel replacement swaps out the breaker panel at the same capacity. A service upgrade increases how much power your home can draw, for example from 100 to 200 amps, and usually involves the meter base, service conductors, and coordination with PG&E. We’ll tell you which one your home actually needs.
They have a well-documented history of breakers that may not trip when they should, which is why many electricians and home inspectors recommend replacing them. We replace Federal Pacific, Zinsco, and old fuse panels regularly.
Not always. A fuse box in good condition can still work, but most were installed when homes used far less power. Oversized fuses, limited capacity, and no room for new circuits are common problems, and some insurance companies ask about them.
Not by itself. A new panel doesn’t change how much power your appliances use. It makes your system safer and gives you capacity to add things like an EV charger or heat pump.
Some do. Insurers and home inspectors often ask about panel brand, age, and whether the home has fuses. If your panel was flagged, we can assess it and give you a written estimate.
Level 2 EV charger installation in Humboldt County — Tesla, Emporia & more. Load calcs and permits handled by a C-10 licensed electrician. Free estimates.
Learn moreFull electrical for new construction in Eureka & Humboldt County. Rough-in to finish for homes, ADUs & shops by a C-10 licensed contractor. Free estimates.
Learn moreCommercial electrical in Humboldt County: service agreements, repairs, 3-phase service, UPS & server room power. Off-hours work available. C-10 licensed.
Learn moreCall, text, or send a few details and Ross or a member of the crew will get right back to you — usually the same business day.
Trouble with the form? Open it in a new tab or call (707) 476-3720.