C-10 #1053285 · Licensed & Insured
Serving Humboldt County since 2015Mon–Fri 7:30am–5:00pmSat 8:00am–3:00pm

Electrical Rewiring in Humboldt County

Older wiring wasn’t built for today’s electrical loads. Greenbelt Electrical replaces outdated and unsafe wiring with safe, code-compliant circuits for homes and buildings across Humboldt County — permitted, inspected, and done by a licensed C-10 crew.

C-10License #1053285
5.0★Google rating · 38 reviews
2015Serving Humboldt County since
Warning signs

Signs your home may need rewiring

  • Two-prong outlets with no ground
  • Knob-and-tube wiring visible in the attic, basement, or crawl space
  • Aluminum branch wiring, found in some homes built in the mid-1960s to mid-1970s
  • Outlets or switches that are warm, discolored, or crackle
  • Breakers that trip often, or lights that flicker for no clear reason
  • A burning smell with no obvious source
  • Brittle, cracked, or cloth-covered wiring insulation
  • An insurance company, lender, or home inspector flagged the wiring
What's included

What this service covers

  • Inspection and assessment of existing wiring
  • Whole-home rewires and room-by-room rewiring
  • Replacement of knob-and-tube, aluminum, and ungrounded (two-prong) wiring
  • New circuits, grounded outlets, and GFCI/AFCI protection to current code
  • Panel upgrades when the existing service can’t support the new wiring
  • Permits and inspection coordination
Why Greenbelt

Why choose Greenbelt for electrical rewiring

Licensed, bonded & insured

California C-10 License #1053285. Rewiring is permitted work that has to pass inspection — it should be done by a licensed contractor.

Straight answers on scope

We tell you what actually needs replacing and what doesn’t, and put it in a written estimate before work starts.

Stay in your home

We shut power off one room at a time, so you can keep living in the house while we work. We protect floors and furnishings and keep wall openings to a minimum.

Local since 2015

Humboldt County has a lot of older housing stock. We’ve been working in it since 2015, based right here in Eureka.

Compare

Older wiring types we replace

These are the older wiring systems we replace, and why they raise concerns.

Comparison of older residential wiring types
Wiring typeTypically installedHow to spot itMain concerns
Knob-and-tubeRoughly the 1880s to the 1940sSingle wires on ceramic knobs and through ceramic tubes, often in attics and crawl spacesNo ground wire; aging insulation; overheating risk when buried in insulation or modified over the years
Aluminum branch wiringRoughly the mid-1960s to mid-1970sSilver-colored wire at outlets and switches; ‘AL’ marking on the cable jacketConnections can loosen and overheat over time, especially at outlets and switches
Ungrounded two-wire cableCommon before the early 1960sTwo-prong outlets; cable with no bare ground wireNo ground path for three-prong appliances, surge protectors, or many modern electronics

Date ranges are approximate and vary by home. We confirm what you have during the assessment.

Pricing

What affects the cost of rewiring

Rewiring costs vary more than almost any other electrical job, so we don’t publish ballpark prices. These are the biggest factors.

Whole home or room by room

A full rewire covers every circuit. Room-by-room rewiring lets you tackle the most urgent areas first.

Size and layout

More square footage, more floors, and more circuits mean more wire and labor.

Access

Open attics and crawl spaces make it easier to run new wire. Plaster walls, finished basements, and tight spaces take more time.

Panel capacity

If the existing panel can’t support the new circuits, a panel upgrade may be part of the project.

Code upgrades

New wiring has to meet current code, which can include grounded outlets, GFCI and AFCI protection, and smoke and carbon monoxide alarm requirements.

Drywall repair

Drywall patching is handled by a separate trade at additional cost, so plan for it in your budget.

Every job is seen in person and quoted in writing before work starts. Call (707) 476-3720 or request a free estimate.

How it works

Our process

  1. Walkthrough & assessment

    We look at your existing wiring, panel, and how you use the space, and identify what needs to be replaced.

  2. Written estimate

    You get a clear written quote with scope, permit requirements, and timeline before any work begins.

  3. Permits & rewiring

    We pull the permit and replace the wiring to current code, working room by room so you can stay in the home. A typical rewire takes about six to seven days.

  4. Inspection & walkthrough

    Work is inspected, and we walk you through what was done before we close out the job.

Local knowledge

Rewiring older Humboldt County homes

Eureka is known for its Victorian-era homes, and older houses are common across Humboldt County. Many still have original or decades-old wiring, sometimes with newer circuits added on over the years.

Rewiring an older home takes care. We work room by room, shutting power off to one area at a time so you can keep living in the house, and keep wall openings as small as possible. A typical rewire takes about six to seven days.

Rewiring is permitted work. We pull the permit and coordinate the inspection with the local building department.

Service area

Available across Humboldt County

Based in Eureka and serving the whole county — including the surrounding North Coast communities.

●Eureka●Arcata●McKinleyville●Fortuna●Ferndale●Trinidad●Blue Lake●Loleta●Cutten

Not sure if you're in our area? Call (707) 476-3720and we'll tell you straight.

Questions

Electrical Rewiring FAQs

Updated

How do I know if my house needs rewiring?

Common warning signs include frequently tripping breakers, flickering or dimming lights, warm or discolored outlets and switches, two-prong ungrounded outlets, a burning smell, or wiring that is decades old. If you notice any of these, have a licensed electrician take a look.

Do you replace knob-and-tube or aluminum wiring?

Yes. We replace knob-and-tube, aluminum, and ungrounded (two-prong) wiring, along with other outdated or damaged wiring we find during the assessment.

Can I stay in my home during a rewire?

Yes. We shut power off room by room rather than to the whole house, so you can keep living in your home while the work is done.

How long does a rewire take?

It depends on the size of the home, access to walls and attics, and how much wiring is being replaced. A typical rewire takes about six to seven days, and we give you a timeline for your home in the written estimate.

Is drywall patching included?

No. Drywall patching and repair is handled by a separate trade at an additional cost. We keep wall openings to a minimum and tell you what to expect before work starts.

Will rewiring require a panel upgrade?

Sometimes. If your existing panel can’t safely support the new circuits, we’ll explain why and include a panel upgrade in the estimate.

Do you pull permits for rewiring?

Yes. Rewiring is permitted work, and we coordinate the permit and inspection as part of the job.

Is knob-and-tube wiring dangerous?

It can be. Knob-and-tube has no ground wire, its insulation breaks down with age, and it can overheat when it’s covered by insulation or has been modified over the years. If your home has it, have a licensed electrician evaluate it.

Is it illegal to have knob-and-tube wiring in California?

Generally no. Existing knob-and-tube isn’t automatically illegal to keep, but it isn’t used for new work, and some insurance companies and lenders ask about it or won’t cover it. Many homeowners replace it before selling, refinancing, or adding insulation.

Can I just swap my two-prong outlets for three-prong outlets?

Not without a ground. A three-prong outlet on an ungrounded circuit looks safer but isn’t. Code allows a few alternatives, such as GFCI protection with proper labeling, but running new grounded wiring is the most complete fix.

Is aluminum wiring safe?

Aluminum branch wiring from the 1960s and 1970s is a known concern because connections can loosen and overheat over time. We replace aluminum wiring and will explain your options during the assessment.

Should I rewire before a remodel?

Yes, if you can. Rewiring while the walls are already open is easier and less disruptive than coming back later. Bring us in before the drywall goes back up.

Keep reading

Related services

Panel Upgrades

Electrical panel upgrades in Eureka & Humboldt County. We handle PG&E scheduling, permits, and inspection. C-10 licensed electrician. Free estimates.

Learn more

Lighting & Retrofit

Lighting retrofits & light pole installation in Humboldt County — recessed lighting, LED pole swaps, parking lots, HOAs & schools. C-10 licensed.

Learn more

New Construction Electrical

Full electrical for new construction in Eureka & Humboldt County. Rough-in to finish for homes, ADUs & shops by a C-10 licensed contractor. Free estimates.

Learn more
Get started

Request your free estimate

Call, text, or send a few details and Ross or a member of the crew will get right back to you — usually the same business day.

Call or text(707) 476-3720
Address1815 B Street, Eureka, CA 95501
Licensed, bonded & insured. California C-10 #1053285 · Serving Humboldt County since 2015.

Trouble with the form? Open it in a new tab or call (707) 476-3720.