C-10 #1053285 · Licensed & Insured
Serving Humboldt County since 2015Mon–Fri 7:30am–5:00pmSat 8:00am–3:00pm

New Construction Electrical Contractor — Humboldt County

Building a home, ADU, or shop in Humboldt County? Greenbelt Electrical handles the full electrical scope — service, rough-in, finish, and inspection coordination — done to code by a licensed C-10 crew that builders and homeowners can actually reach.

C-10License #1053285
5.0★Google rating · 38 reviews
2015Serving Humboldt County since
Plan ahead

What to decide before rough-in

These are easy to get right before the walls close, and expensive to change after.

  • Where the main panel and any subpanels will go
  • Service size, based on planned appliances, heat pumps, and EV charging
  • An EV-ready circuit or conduit to the garage or parking area
  • Lighting layout, switch locations, and dimmers
  • Kitchen, laundry, and workshop circuits
  • Low-voltage and data runs for networking, TV, and security
  • Exterior outlets and lighting
  • Circuits for a future hot tub, shop equipment, or other large loads
What's included

What this service covers

  • Complete wiring for new homes, ADUs, garages, and detached shops (including subpanels)
  • Service equipment and panel installation sized for modern loads
  • Lighting and outlet layout review so rooms work the way you will live in them
  • Dedicated circuits for kitchens, laundry, workshops, and future EV charging
  • Low-voltage and data rough-in included
  • Rough-in and final inspection coordination with the local building department
Why Greenbelt

Why choose Greenbelt for new construction electrical

One accountable contractor

You deal directly with Ross and the Greenbelt crew — the same C-10 licensed team from rough-in through the final walkthrough, not a rotating cast of subs.

Local code knowledge

Building across Eureka, Arcata, McKinleyville, Fortuna, and the rest of Humboldt County since 2015, we know the local inspectors and jurisdictional requirements.

Built for the future

Panel capacity, EV-ready circuits, and sensible outlet placement are cheap to include during construction and expensive to retrofit. We help you get them in now.

Owner-builders and GCs welcome

Whether you’re a general contractor or building your own place, we work directly with you and fit into your project sequence.

Compare

Rough-in vs. finish electrical

Comparison of rough-in and finish electrical stages
StageWhen it happensWhat gets doneInspection
Rough-inAfter framing, before insulation and drywallBoxes set, wiring and low-voltage/data runs installed, service equipment placedRough-in inspection before walls are closed
Finish (trim-out)After drywall and paintOutlets, switches, and fixtures installed; panel terminatedFinal electrical inspection

Exact sequencing depends on your project and the local building department.

Pricing

What affects the cost of new construction electrical

We price new construction from your plans and a scope walkthrough. The main factors are below.

Square footage and circuits

More rooms and more circuits mean more wire, devices, and labor.

Service size and equipment

Larger service and additional subpanels add equipment cost.

All-electric or mixed fuel

Heat pumps, induction cooking, and electric water heating need more capacity and dedicated circuits.

Low-voltage and data

Networking, TV, and security runs are part of our scope; more runs mean more labor.

Detached buildings

Feeding an ADU or shop from the main service may need trenching and a subpanel.

Fixtures and controls

Recessed lighting, specialty fixtures, and smart controls add parts and labor.

Every job is seen in person and quoted in writing before work starts. Call (707) 476-3720 or request a free estimate.

How it works

Our process

  1. Plan review & estimate

    Send us your plans or a scope description. We walk the project, answer questions, and give a written estimate.

  2. Design & layout walkthrough

    Before rough-in, we walk the framed structure with you or your builder to confirm panel location, lighting, switches, and dedicated circuits.

  3. Rough-in

    Service, circuits, boxes, and wiring go in. Rough-in inspection is scheduled with the building department.

  4. Finish

    After drywall and paint, we install devices, lighting, and panel termination, then coordinate the final inspection.

Local knowledge

Building in Humboldt County

We’ve wired new homes, ADUs, garages, and detached shops across Eureka, Arcata, McKinleyville, Fortuna, and the rest of the county since 2015. Each jurisdiction has its own building department and inspection process, and we coordinate the rough-in and final inspections for you.

California’s building codes ask more of new homes than they used to, including EV-ready requirements for many new homes and “electric-ready” provisions in the energy code. We plan for those from the start, so inspections go smoothly and your home is ready for what comes next.

We work with general contractors and owner-builders alike.

Service area

Available across Humboldt County

Based in Eureka and serving the whole county — including the surrounding North Coast communities.

●Eureka●Arcata●McKinleyville●Fortuna●Ferndale●Trinidad●Blue Lake●Loleta●Cutten

Not sure if you're in our area? Call (707) 476-3720and we'll tell you straight.

Questions

New Construction Electrical FAQs

Updated

Is low-voltage and data wiring included?

Yes. Low-voltage and data rough-in is included in our new construction scope, so networking and low-voltage runs go in with the rest of the wiring.

When should I bring the electrician into a new build?

As early as possible — ideally during planning or before framing is complete. Decisions like panel location, service size, and EV-ready circuits are much easier (and cheaper) before walls are closed.

Do you wire ADUs and detached shops?

Yes. Accessory dwelling units, garages, and shops are a big part of new construction work in Humboldt County, including subpanels fed from an existing service where appropriate.

Who handles permits and inspections?

We do. Electrical permits and inspection scheduling with the local building department are part of our new construction scope.

How do you price new construction electrical?

From your plans and a scope walkthrough. You receive a written estimate before work starts.

Do you work with owner-builders as well as contractors?

Yes — we work with both general contractors and owner-builders managing their own projects.

Can you plan for an EV charger even if I don’t have an EV yet?

Yes, and we recommend it. A dedicated conduit and circuit run during construction costs a fraction of retrofitting later, and your panel will be sized to handle it.

Do new homes in California have to be EV-ready?

In many cases, yes. California’s green building code (CALGreen) requires new one- and two-family homes with attached private garages to include EV charging provisions. We plan for it from the start.

Can you wire a detached ADU from my existing house?

Often, yes. Many ADUs are fed by a subpanel from the main service. Whether your existing service has enough capacity depends on a load calculation, and sometimes a service upgrade makes more sense. We’ll lay out the options.

What is the difference between rough-in and finish electrical?

Rough-in happens after framing, when boxes, wiring, and low-voltage runs go in before the walls are closed. Finish happens after drywall and paint, when outlets, switches, and fixtures are installed. Each stage has its own inspection.

Should I plan for a heat pump or induction range even if I’m using gas now?

It’s worth it. Running the circuits or conduit during construction costs much less than opening walls later, and current California energy code includes electric-ready provisions for some gas appliances.

Keep reading

Related services

Panel Upgrades

Electrical panel upgrades in Eureka & Humboldt County. We handle PG&E scheduling, permits, and inspection. C-10 licensed electrician. Free estimates.

Learn more

EV Charger Installation

Level 2 EV charger installation in Humboldt County — Tesla, Emporia & more. Load calcs and permits handled by a C-10 licensed electrician. Free estimates.

Learn more

Commercial Electrical

Commercial electrical in Humboldt County: service agreements, repairs, 3-phase service, UPS & server room power. Off-hours work available. C-10 licensed.

Learn more
Get started

Request your free estimate

Call, text, or send a few details and Ross or a member of the crew will get right back to you — usually the same business day.

Call or text(707) 476-3720
Address1815 B Street, Eureka, CA 95501
Licensed, bonded & insured. California C-10 #1053285 · Serving Humboldt County since 2015.

Trouble with the form? Open it in a new tab or call (707) 476-3720.