Panel Upgrades
Electrical panel upgrades in Eureka & Humboldt County. We handle PG&E scheduling, permits, and inspection. C-10 licensed electrician. Free estimates.
Learn moreCharge at home overnight instead of hunting for a public station. Greenbelt Electrical installs Level 2 home EV chargers the right way — dedicated circuit, proper load calculation, and a clean finish — across Eureka, Arcata, McKinleyville, and all of Humboldt County.
EV chargers pull a continuous 40–80 amp load. As a California C-10 licensed contractor (#1053285), we size the circuit, wire, and breaker correctly — not just "make it work."
Older Eureka and Arcata homes often have 100-amp panels that are already near capacity. Serving Humboldt County since 2015, we know what to look for before quoting.
If your panel does need an upgrade, we can handle both in the same project — see our panel upgrade page and ask about doing the work together.
Conduit runs and mounting are done cleanly and to code, so the install looks like it belongs on your home.
Most EV owners end up with Level 2 at home. Here’s how the options compare.
| Option | Power | Charging speed | Good fit for |
|---|---|---|---|
| Level 1 (standard outlet) | 120 volts, existing outlet | Slowest; a fully depleted battery can take more than a day | Plug-in hybrids and short daily commutes |
| Level 2 plug-in | 240-volt outlet on a dedicated circuit | Several times faster than Level 1; most EVs refill overnight | Drivers who may want to take the charger with them |
| Level 2 hardwired | 240 volts, wired directly to a dedicated circuit | Several times faster than Level 1; supports higher charging rates than a plug-in | Permanent installs, outdoor locations, and the fastest home charging |
Actual charging speed depends on your vehicle, the charger, and the size of the circuit.
Most of the cost comes down to your panel and how far the power has to travel.
If your panel has room and capacity, the install is simpler. If it doesn’t, a panel upgrade or a load-managed charger may be needed.
A charger near the panel needs a short run. A detached garage or a driveway on the far side of the house needs more wire and conduit, and sometimes trenching.
Higher-amperage chargers need larger wire and breakers, and hardwired and plug-in installs are wired differently.
Outdoor installs need weather-rated equipment and connections that hold up to our wet coastal winters.
Running power underground or through finished walls adds labor.
EV charger circuits typically need a permit and inspection, which we handle for you.
Every job is seen in person and quoted in writing before work starts. Call (707) 476-3720 or request a free estimate.
Call or request an estimate. We ask about your vehicle, where you park, and your current panel.
We inspect your panel, measure the run to your parking spot, and give you a written quote with no surprises.
The dedicated circuit is run, the charger mounted and connected, and everything labeled in your panel.
We test the circuit under load, show you the charger operation, and leave the area clean.
Many homes in Eureka, Arcata, and McKinleyville were built long before EVs, and their panels often have limited spare capacity. That’s why every install starts with a load calculation, so the charger works reliably and your panel isn’t overloaded.
Our wet coastal weather matters too. Carport and driveway installs get weather-rated chargers, fittings, and conduit, with penetrations sealed so the install holds up through the rainy season.
We handle permits in every Humboldt County jurisdiction, and we install chargers for homes, businesses, apartments, and multi-unit properties.
Based in Eureka and serving the whole county — including the surrounding North Coast communities.
Not sure if you're in our area? Call (707) 476-3720and we'll tell you straight.
Updated
It depends on your panel size and existing loads. We perform a proper load calculation before quoting, and if your panel is undersized we can quote an upgrade at the same time.
EV charger circuits typically require an electrical permit and inspection. We handle the permit and inspection as part of the job, in every Humboldt County jurisdiction.
Plug-in chargers need a properly installed 240-volt outlet on a dedicated circuit. Hardwired chargers must be permanently wired by a qualified installer. Continuous EV load is hard on undersized circuits — this is not a DIY job.
A typical home charger install takes about three to six hours. Longer runs, trenching, or panel upgrades take more time — we confirm the timeline in your written quote.
We install Tesla, Emporia, and Cutler-Hammer chargers. Already bought a different charger? Tell us the make and model and we’ll confirm it before quoting.
Yes. We install EV chargers for homes, businesses, apartments, and multi-unit properties. Commercial and multi-unit installs are quoted separately based on load, trenching, and equipment.
It depends on the charger. EV charging counts as a continuous load, so the circuit is sized at 125% of the charger’s rated current. For example, a charger set to 48 amps needs a 60-amp circuit. We match the charger setting, wire, and breaker to what your panel can support.
Hardwired is usually the better choice for a permanent install. It supports higher charging rates and avoids wear on an outlet. A plug-in charger on a 240-volt outlet makes sense if you want to take the charger with you. We’ll walk you through both.
Yes. Many chargers are rated for outdoor use. We mount them with weather-rated fittings and conduit so they hold up to Humboldt County rain.
Not always. Many homes have enough capacity for a properly sized charger. If yours doesn’t, the options include a panel or service upgrade, or a charger with load management that limits charging when the house is using a lot of power. The load calculation tells us which applies.
Sometimes. Incentive programs change often, so check current offers from PG&E, the Redwood Coast Energy Authority, and your vehicle’s manufacturer before you buy.
Electrical panel upgrades in Eureka & Humboldt County. We handle PG&E scheduling, permits, and inspection. C-10 licensed electrician. Free estimates.
Learn moreCommercial electrical in Humboldt County: service agreements, repairs, 3-phase service, UPS & server room power. Off-hours work available. C-10 licensed.
Learn moreFull electrical for new construction in Eureka & Humboldt County. Rough-in to finish for homes, ADUs & shops by a C-10 licensed contractor. Free estimates.
Learn moreCall, text, or send a few details and Ross or a member of the crew will get right back to you — usually the same business day.
Trouble with the form? Open it in a new tab or call (707) 476-3720.